2006:05:21	2006:05:21	2006:07:22	2006:07:22	2006:07:23
	leading edge former	leading edge former	nose rivet template	nose skin layout	nose in jig

	2006:07:23	2006:07:23	2006:07:23	2006:07:31	2006:07:31
	clecoed nose	me and my nose	my nose and I	completed center nose	completed center nose

	2006:07:31	2006:08:01	2006:08:01	2006:08:21	2006:08:21
	laying out panel nose	drilling panel nose in jig	clecoed panel (tank) nose	riveted panel (tank) nose	riveted panel (tank) nose

	2006:08:21	2006:08:21	2006:10:08	2006:10:08	2006:10:08
	tank fuel cap/vent	access panel/inner rib	rib brackets on spar	tank drain	nose nut plate

	2006:11:07	2006:11:07	2006:11:07	2006:11:07	2006:11:07
	alignment water level	aligning for twist	more alignment	drilling rib attach brackets	more alignment

	2006:11:17	2006:11:17	2006:11:17	2006:11:21	2006:11:21
	alignment w/ laser pointer	laser target on ceiling	clamped for side motion	drill layout	drill/cleco left top

	2006:11:21	2006:11:21	2006:12:03	2006:12:03	2006:12:03
	more skin layout	skins all drilled	aligning outer nose/spar	fine tuning	drilling panel nose/spar

	2007:06:10	2007:06:10	2007:06:10	2007:06:10	2007:06:10
	left nose w/ tank back	lt. spar/tank back gap	rt. nose	rt. nose & tank back	rt. tank back initial fit

	2007:06:10	2007:06:10	2007:06:13	2007:06:16	2007:06:16
	rt. tank back first clecoes	rt. tank back drilled	rt. tank & spar clecoed	drilled rear spar	ribs clecoed to rear spar

	2007:06:17	2007:06:17	2007:06:17	2007:06:17	2007:06:17
	flanging outer ribs	beading outer ribs	outer ribs ready	outer spars attached	outer spars attached

	2007:06:17		2007:06:21		2007:07:01
	outer rt. rib fitting	drilling outer rib attach	mounting lt panel ribs	mounting lt panel ribs	final lt. rib fitting

	2007:07:01	2007:07:01	2007:07:29	2007:07:29	2007:07:31
	final lt. rib fitting	final lt. rib fitting	final lt. rib fitting	skinning bottom lt panel	skinning top lt panel

	2007:07:31	2007:08:04	2007:08:04	2007:08:06	2007:08:06
	skinning top lt panel	dimpling top lt panel	dimpling top lt panel	lt outer hinge stiffener	lt center hinge stiffener

				2007:10:03
	stiffening brackets on 7L	dimpling top R skin	drilling top R rear	drilling top R rear	initial aileron skin bend

	2007:10:03			2007:10:04	2007:10:04
	bending other aileron	aileron spar blanks	bending aileron spars	bending aileron spars	bent aileron spars

		2007:10:04	2007:10:04	2007:10:20	2007:10:21
	bent aileron spars	fitting spar to aileron	fitting spar to aileron	spar extension blanks	formed spar extensions

	2007:10:31	2007:10:31	2007:11:01	2008:05:31	2008:05:31
	fitting RH extension	RH wing tip fitting	RH wing tip fitting	RH wing tip fitting	RH wing tip fitting

	2008:05:31	2008:05:31	2008:05:31	2008:06:01	2008:09:01
	RH wing tip fitting	RH wing tip fitting	RH wing tip fitting	RH wing tip fitting	RH aileron, bottom

	2008:09:01	2008:09:01	2008:09:01	2008:09:01	2008:09:01
	RH aileron end cap	RH aileron end cap	RH aileron end cap	RH aileron end cap	RH wing tip fitting

	2008:09:01	2008:09:01	2008:09:13	2008:09:13	2008:09:17
	RH wing tip fitting	RH wing tip fitting	RH wing tip fitting	RH aileron end cap	LH outer rear spar trim

	2008:09:17	2008:09:21	2008:09:21	2008:09:21	2008:09:23
	LH rear spar drilling bot	LH rear spar drilling top	LH aileron hinge fitting	LH aileron fitting	LH aileron setting twist

	2008:09:25	2008:09:25	2008:09:25	2008:09:25	2008:09:25
	LH aileron fit with gap seal	LH spar extension fitting	LH spar extension fitting	LH spar extension fitting	LH wing tip skin fitting

	2008:09:25	2008:09:26	2008:09:27	2008:09:27	2008:11:04
	LH wing tip skin fitting	LH wing tip skin fitting	LH wing tip skin fitting	LH wing tip skin fitting	wing attach access holes

	2008:11:04	2008:11:06	2008:11:06	2008:11:06	2008:11:06
	wing attach access holes	wing!!!	wing!!!	wing!!!	rear spar attach

	2008:11:06	2008:11:06
	wing joint fitting	rear spar attach